Always use appropriate safety equipment when using the tools. Always use goggles when using the air dusting gun. Always use a suitable mask when using the paint spray gun. These are easily available from any DIY shop.

• Gravity fed spray gun

• Suitable for spray painting on  Metal or wood

• Better paint efficiency due to gravity fed spray gun

• 0.5lt pot

• Adjustable nozzle 1.5mm 

• Working pressure : 3-4 bar

• Air consumption : 120-180lt / min

Filling The Spray gun
Fill the container with the type of material required which is diluted to the correct consistency, for spray painting using the appropriate thinner.
You can use emulsion paints, preservatives and most products suitable for spraying when adequately thinned with the appropriate thinner, directions for thinning should be sought from the manufacturer , however as a general rule of thumb, if a wooden spatula or stick used for stirring the material is lifted from the product there should be 3 drips and no more, as a guide only.  
Click here to view: Tips for Spray Painting

How to use the low-pressure spray gun :
Fill the container with the type of material required which is diluted to a Correct consistency for spray painting using the appropriate thinner. Re-attach the container to the gun Connect the accessory to the spiral-wound tube and to the compressor Press the trigger to operate the spraying of the chosen material. Adjust the jet of paint using the ring-nut . Always clean the spray gun carefully after use. Do not use wire brushes or Abrasives. Do not submerge the parts in solvent as this will damage the Internal seals.

Note: it is normal for this spray gun to vent air continuously through the Nozzle Clean the nozzle carefully after use. For this purpose, fill the reservoir with Thinner (or water for water based materials) and spray in a safe direction to remove ALL material residue.

WARNING!!!: Never leave paint inside the reservoir when not in use. Dried paint damages the spray gun's precision components beyond repair.

AIR PRESSURE
Adjust regulator knob (Fig. 4) to “low-medium” depending on material of Application when using the low pressure spray gun

• Air inflating gun

• With 60 mm gauge to inflate tyres,

• Universal fitting suitable for most types of tyre

• Working pressure : 3 bar

• Air consumption : 50lt / min

How to use the inflation gun:

Once you have connected the accessory to the spiral-wound tube and to the compressor, unscrew the plug of the valve on the rim of the Tyre. Connect the end of the inflation gun to the valve of the tyre and make sure it is securely fastened. To inflate the tyre, start the compressor and press the trigger until the pressure required, shown on the gauge, is reached. The inflation of footballs, air beds, bicycle tyres etc, can be carried out using the adaptors supplied. The adaptors can be attached to the inflating gun by pressing the clip at the end of the tube connected to the inflating gun, then push firmly the chosen adaptor into the nozzle and release the clip to secure. For further information regarding the recommended pressure for tyre inflation, refer to the maintenance handbook of your car.

WARNING!!!: the accessory provided in the kit must be used only to inflate car tyres. To inflate other objects such as balls, mattresses etc., ask your retailer for the 3-needle adapter kit.
 

AIR PRESSURE
Adjust regulator knob (Fig. 4) to setting from “low-high” depending on the speed of inflation required when using the inflating gun.

• Wash gun

• To be connected to water and air supply

• Can vary water pressure

• Suitable for washing cars, patios, garden furniture etc.

• Working pressure : 4-7 bar

• Air consumption : 100-120lt / min

How to use the washing gun:

Once you have connected the accessory to the spiral-wound tube and to the compressor, connect the washing gun to a water hose If the end of your hose is not fitted with a universal fast attachment, simply insert the fitting of the gun in the hose and tighten with a hose clamp. To use the accessory, start the compressor, direct the gun in the direction of the surface to be washed and press the trigger. Best cleaning results are obtained at maximum water pressure i.e. turn the water tap to full on.
Remember that you can adjust the spread of the water jet using the ring-nut at the base of the nozzle.

WARNING!!! Never use the jet of water on objects that may be damaged by the pressure of the water.

AIR PRESSURE
Adjust regulator knob to “high” when using the washing gun

• Blow gun

• For blow dusting of dust, wood chips, gravel, filings, swarf etc.

• Working pressure : 4 bar

• Air consumption : 150lt / min

How to use the air dusting gun:

Once you have connected the accessory to the spiral-wound tube and to the compressor, aim the gun in the direction of the surface required and press the trigger.

AIR PRESSURE
Adjust regulator knob  to “low” when using the air dusting gun